3YRS
GENTIGER MACHINERY INDUSTRIAL CO., LTD.
886-4-26836919
886-4-26839900
No.66, Lane 100, Shueitou 1st Road, Waipu Dist., Taichung City 438, Taiwan
www.gentiger.com.tw

Products

High speed 5-axis machining center
High speed 5-axis machining center GT-HTA2500
GT-HTA2500

Feature

A High-Tech Machining Center
Packed with many outstanding features, the advanced GT-HTA 2500 5-axis machining center is designed for high speed and vibration free performance. This will dramatically reduce your machining time. With its rotating and tilting spindle head, the machine allows complex parts to be machined in only one setup.

5-axis machining center combining A, C-axis on spindle head 18,000 rpm high speed, built-in type spindle.
Roller type linear guide ways on x, y, z-axis.
Special double-column, high speed machine structure for high speed and heavy cutting.
One-piece constructed columns feature extra high rigidity.
Heidenhain optical scales on 3 axes.
High Speed! Maximum Stability! Lifetime Accuracy!
These are the qualities that every operator demands and gets with the Gentiger GT-HTA 2500 5-Axis Machining Center. It’s a high precision, multi-tasking machine, suitable for high precision machining.
6 Blocks on Z-axis
Slideways are mounted with two heavy duty roller type linear guide ways with great span between ways. Each linear guide way employs three blocks to upgrade rigidity on Z-axis and features maximum stability during heavy cutting.
Three Linear Guide Ways on X, Y-axis
X, Y-axis is mounted with three heavy-duty roller type linear guide ways with greater span between ways. This provides solid support for table. Another benefit is the table can accommodate heavier loads without deformation.
Chip Augers
There is one chip auger each equipped at side of base, delivering chips to a chip conveyor for easy removal.
Rigid Roller Type Linear Guide Way
Mounted with the SRG highly rigid roller type linear guide ways combined with the use of a roller retainer. These special linear guide ways feature low friction coefficiency, smooth movement and maintenance-free performance for long periods of operation.
Heidenhain Optical Scales on 3 Axes
High accuracy (±3μm)
High repeatability accuracy (≦0.2μm)
Pollution resistant (single field scanning)
Interfering signal-resistant (covered by full conductor)
Optimal Structural Design
Double column structure features ultra-high stability in high speed machining.
The table is independently installed on the base and fully supported by 3 roller-type linear guide ways through the entire stroke, assuring maximum accuracy and dependability.
One-piece Constructed Columns
The specially designed double-column, high speed machine structure combined with one-piece constructed column fully exhibit structural rigidity and stability during heavy cutting.
Three Axes Linear Guide Ways
Roller type linear guide ways on three axes feature higher feed rate, resist heavier loads and ensure superior dynamic accuracy and long service life.
X,Y-axis is equipped with 3 linear guide ways for superior rigidity.
Servo Motor Drives on 3 Axes
Three axes are driven by powerful servo motors. Their power can reduce machining time for large molds and increase profitability.
Deformation Free
All casting parts are stress relieved and treated for lifetime accuracy without any deformation.
High Accuracy
Positioning accuracy: 0.003 / 300 mm
Repeatability: ±0.003 mm
Three axes are equipped with Heidenhain optical scales.
Three Axes Feed Rates
Rapid feed rate: 20 / 15 / 20 m/min.
Cutting feed rate: 20 / 15 / 20 m/min.

Specification

Specification

MODEL  
Travel (X, Y, Z) 2500 x 2470 x 850 mm
Table area 2800 x 1600 mm
Max. Spindle speed 18,000 RPM
Type of spindle motor Built-in
Spindle taper HSK-A63
Tilting angle A axis ±115° C axis ±220°
Drive Direct drive motor
Speed 30-40 rpm
Max. Torque 800 Nm
Positioning (indexing) accuracy ±10 sec
Repeatability ±7 sec
ATC capacity 24 tools

*Other spindle speed also available with this machine.

STANDARD ACCESSORIES

  • Coolant tank
  • Work lamp
  • Tool box
  • Coolant pump
  • Coolant system
  • Spindle cone air blast
  • Air conditioner for electrical cabinet
  • M.P.G
  • Pilot lamp
  • Spindle thermo compensation function
  • Caterpillar type chip conveyor and chip cart
  • Central lubrication system
  • Operation and maintenance manuals
  • Leveling bolts and blocks
  • Two chip augers beside work table
  • Ethernet socket
  • X,Y,Z axes optical scale
  • A,C axes angle encoders

 OPTIONAL ACCESSORIES

  • Oil skimmer
  • Automatic tool length measurement
  • Automatic workpiece measurement
  • Coolant through spindle

Mold
Machine
Vehicle
Contact Supplier
Browsing History
Scroll Up
EZB2B.TW uses cookies,IP to collect data and continually improve the website. By continuing to use this website, you must agree to the use of cookies and IP.